#WPA2 WORDLIST 2016 PASSWORD#

If successful, Reaver will display the WPA/WPA2 password (PSK), but note that Reaver doesnвЂ™t crack WPA/WPA2, only WPS.ДЄndrodumpperВ is an app for rooted androids capable of carrying this attack.ДЄs a mechanism of defence against this attack, many APs will lock WPS after several wrong PINs.

The attack usually takes less than 15 hours. i specifies the interface, -c the channel, -b the bssid of the target AP, and -vvВ for very verbose. Then start the attack on your target, for example with Reaver: Wash -iВ Figure 3: example of wash result To know if an AP is potentially vulnerable to this attack, check if it supports WPS using either airodump-ng: This makes a bruteforce approach very practical. You can read the details in the paper written by the guy who discovered the attack. Since the PIN is 8 digits long, one could expect that the number of possible pins would be 10 8В , however,В because of design flaws, there are only 11вЂ™000 possible candidates.

Push the button: The user pushes a button (physical or virtual) on both the AP and the enrollee in a short period of time (e.g.

PIN: The user reads a number (typically found on the bottom of the router) and enters it on theВ client (the enrollee), or vice-versa.

There exist two modes that must be implemented by every AP offering WPS: Its purpose is to ease the setup/authentication process for users with little wireless configuration knowledge. It allows a user to connect to an AP without specifying the password (PSK). WPS is a security mechanism offered by certain WPA/WPA2 access points. This is why WEP is deprecated and should never be used. The tricked AP will rebroadcast the requests and generate new IVs :ДЇinally, in another console, crack the password: In another console, listen for ARP requests and reinject them. Lock your interface on the same channel as your target:ДЄirodump-ng -c -bssid -w capture-file See the Fluhrer, Mantin and Shamir attack. Sniffing enough traffic enables an attacker to crack the key. The design of WEP violates this assumption and repeats themВ quite often: IVs of standard WEP are 24 bits long (this gives a space of 2 24), the maximum length of an IP datagram sent over an Ethernet is 1500 octets (sic rfc894), 802.11gвЂ™s maximum speed is 54Mbps, so by the pidgeon hole principle we will have a repetition after at most (2 24В + 1) * (1500 * 8) / (54*10 6) seconds, so roughly 1 hour. WEP uses RC4В keys.В RC4 requires a random or pseudo-random initialization vectors (IVs). The great weakness of WEP is its use of staticВ keys: they have to be set manually, and both the AP and every connected client have the same key to encrypt traffic. WEP was used fromВ 1997 to 2003В until it was deprecated due to its weak security.

#WPA2 WORDLIST 2016 MAC#

Ifconfig down & macchanger -m 00:20:91:11:22:33 wlan0mon & ifconfig wlan0mon up Figure 2: changing your MAC address WEP вЂ“ Wired Equivalent Privacy It displays a list of detected access points (APs вЂ“ the ones we will attempt to gain access to) and a list of connected clients, or stations (STA вЂ“ phones, laptops, etcвЂ¦ connected at this moment to an AP). Put your card in monitor modeВ and scan for APs and connections with airodump-ng:ДЇind out the interface name of your adapter using ifconfig and start it inВ monitor mode В open a terminal and type the following commands:ДЄirodump-ng should yield an output like this: Figure 1: example of airodump-ng results

Run the VM and physically unplug/replug and you should be good to go.

#WPA2 WORDLIST 2016 PLUS#

To make your adapter usable in VirtualBox, go to the settings and choose USB.В Now add your device with the plus button on the right.

Before buying one, verify that it is compatible with Kali.

#WPA2 WORDLIST 2016 INSTALL#

Optional (if you donвЂ™t want to use a VM and will install Kali straight on your computer): a Wireless USB adapter if you run Kali in a VM.

Be sure to install the guest additions if you run it in a VM.

A version of Kali LinuxВ : a Linux distro designed for penetration testing that comes by default with all the tools we will be using.

Step 5: Spawns a MDK3 process, which deauthenticates all users connected to the target network, so they can be lured to connect to the FakeAP and enter the WPA password.It goes without saying that you should not use the techniques described below without the consent of the wireless owner.

Step 4: Launch a FakeAP instance to imitate the original access point Step 2: Capture a handshake (canвЂ™t be used without a valid handshake, itвЂ™s necessary to verify the password)

Wpa2 wordlist 2016